I posted this in SugarKang's thread but I thought this might get more traffic.
I have a DIR615RevC1. I am able to connect and get back DNS servers from my DSL provider (PRIMUS). My clients get back IPs from the router and seem to be happy.
The problem is I get to access to the internet. I see some WAN traffic when requesting pages, so it looks like it has problems getting back onto the LAN.
Any ideas? I've played around with some settings, but I'd much rather know some good debugging steps (via telnet?, I'm a linux beginner, I know a bit)
Thanks,
Mike
i am in a diff situation, im doing client bridge, and it seems to connect to my other ddwrt as far as seeing it in the wireless (status) tab, but I get no connection no ping no nothing... :/
the dir-615 using the latest ddwrt firmware but my other routers are using 13577M NEWD Eko on my Netgear WNDR3300, and my Linksys WRT350N is using revision 13064
:roll:
does anyone have a clue why I cant get client bridge mode to work on this dir-615 E3, it shows it connects as far as status, strength of signal etc... but I get no ping nothing, I have fallowed the wiki guides and have done it to other routers (the netgear 3300's one is connecting as client bridge with one of the radio's and the other radio is acting as AP)
Hi guys, could you explain further what I need to do with my D-Link 615 router?
I have the following:-
HW D4
FW 1.00VG
Can anyone suggest how exactly I edit the hex file or if possible provide me with a correctly edited one for my device?
The following link states "[For H/W D2 F/W 1.00VG skip steps 2-3 below, I found downloading "dlink-dir615d-factory-webflash.bin" 2010-08-09 directly worked fine AFTER restoring the device to the manufacture defaults (using the web interface maintenance -> reset to factory settings)]
"
http://www.dd-wrt.com/wiki/index.php/DIR-615C
If mine is a D4 would it be the same as D2 in regards to this?
Got my DIR-615-C1 up to build 16785 now and it's working nicely as a client bridge... except that after a while (haven't determined exactly how long yet) it just seems to stop responding completely, requiring a power cycle even to connect to it via LAN.
Anyone else experience this? Any suggestions what I could tweak that might help?
Whats the best wireless settings? I have a 615 D4 and getting useless s best speeds. Whats the best setup for tx etc. I have N speed wireless card in laptop.
I post it in separate topic, but have no answer there. Can anybody help with this snag?
Hello! I change my firmware to latest dd-wrt.And setup the l2tp access (set login - pass - vpn server), turn off firewall. But I can't connect to internet. The router get IP, GATE and mask (i see it status tab), but in status->WAN it is Disconnected and when I press connect, it's do nothing. After it I make 30-30-30 and setup router again, but it has no result. I enter via telnet and make ifconfig dump.
Hi i have a DIR-615 C2 And i flashed latest dd-wrt and the wireless is not working at all the led on the router is not on and the wireless settings in the webgui just not there and i tried everything i could and i cant make the wireless work
i am in a diff situation, im doing client bridge, and it seems to connect to my other ddwrt as far as seeing it in the wireless (status) tab, but I get no connection no ping no nothing... :/
the dir-615 using the latest ddwrt firmware but my other routers are using 13577M NEWD Eko on my Netgear WNDR3300, and my Linksys WRT350N is using revision 13064
does anyone have a clue why I cant get client bridge mode to work on this dir-615 E3, it shows it connects as far as status, strength of signal etc... but I get no ping nothing, I have fallowed the wiki guides and have done it to other routers (the netgear 3300's one is connecting as client bridge with one of the radio's and the other radio is acting as AP)
I need to know what I might be missing :/
I have the same situation. I get trough using the VAP (Virtual Access Point), but not trough ethernet.
Under STATUS --> Wireless it shows TX Power of 13 and that doesn't change no matter what I try to set it to and rate of 75MB/s though thats higher than usually as it has been at or around 30 all day
Thanks for the help in advance
I'm experiencing similar problem here with build 16454. Im my Sys-info menu no matter what a change in setup can't increase TX Power over 20 dBm.
My current setup:
dir-615 E5
Wireless mode AP
Wireless Network NG-Mixed
Channel width Full(20 mhz)
Channel 11
Advanced settings:
Tx Power 70 dBm
Antenna Gain 0 dBi
Protection mode none
RTS Threshold disable
Short Preambrl disable
TX Antenna Chains 1+2
RX Antenna Chains 1+2
Ap isolation disable
Sensitivity Range 2000
Max Associated Clients 256
I have the EXACT same problem of wireless radio stopping at some random time (could be up to 3 days, or even 1 week, or even 1 hour before it stops). I have to reboot the router to get wifi back.
Firmware Version: E3
minhneo wrote:
I have:
Router Model
D-Link DIR-615-C1
Firmware Version
DD-WRT v24-sp2 (08/07/10) std - build 14896
Every few hours, my wireless radio stops broadcasting and cannot be seen by wireless clients. I must unplug then plug in power. Please help me!
